InterNACHI


Go Back   InterNACHI Inspection Forum > General Inspection Topics > Miscellaneous Discussion for Inspectors

Notices

Miscellaneous Discussion for Inspectors Discuss whatever you wish in this forum.

 
Reply
 
LinkBack Thread Tools
  #16  
Old 2/6/09, 1:13 PM
klott's Avatar
klott klott is offline
InterNACHI Member
 
Join Date: Jan 2007
Location: monroe, ga
Posts: 8,707
Default Re: Non-members can still post on this message board.

Quote:
Originally Posted by inxil View Post
Ken,

You don't have the "Report Post" button?
I do since I rejoined, but before I did not.



"It's not what you believe that matters...it matters what you believe!"
Reply With Quote
  #17  
Old 2/6/09, 1:15 PM
Ed Fako's Avatar
Ed Fako Ed Fako is offline
Active Poster
 
Join Date: Feb 2007
Location: NW Chicago Suburbs
Posts: 199
Please Note: Ed Fako is a non-member guest and is in no way affiliated with InterNACHI or its members.
Default Re: Non-members can still post on this message board.

What I don't get about the new rule, is what does it prevent?

If someone were to post Spam or Inflammatory Remarks, then other members would hit the Report Post Icon to report it to the moderators immediately. Thats when a post should deserve moderation.

I see this as increasing the moderating tasks more than assisting in the duties to diminish their work load.

I know first hand, because I moderate on www.ContractorTalk.com which has over 40,000 members and www.DIYchatroom.com which has over 45,000 members and several Roofing related sites. If I had to add Moving Approved Posts to the duties, I wouldn't have time to keep up.

I just try to offer practical real world experience commentary to assist those that run into typical situations, but have not actually done the roofing or ventilation tasks before themselves.

I don't know how long it took to get posted. The one answer to another thread and this question both were not available for me to see, so I left the forum last night to wait for the response to this question.

It sucks the wind out of the continuity of a discussion, like one thread which requested questions to be considered for a roofing guide book. I never would have posted more than one situation, had I not gotten instant response and feedback.

I am sure you put some thought into this action, but it probably had more to do with inflammatory posters, which I do not consider myself to be.

See if you guys in charge can reconsider that rule please. As diplomatically as this statement can be said, this rule Sucks, in my own humble opinion.

Or, the very least, have an option for a gratis affiliate membership for posters considered worthwhile to have on board, since I do not plan on opening up a Home Inspection business to compete with you guys. Maybe some sort of probationary status for an unknown personality new to posting on this site could be considered.

Does that seem reasonable to you?

Ed
Reply With Quote
  #18  
Old 2/6/09, 1:20 PM
Chris Morrell's Avatar
Chris Morrell Chris Morrell is offline
Director of IT
 
Join Date: Aug 2002
Location: Philadelphia, PA
Posts: 1,627
Send a message via ICQ to inxil Send a message via AIM to inxil Send a message via MSN to inxil Send a message via Yahoo to inxil
Default Re: Non-members can still post on this message board.

Ed,

Once we have more moderators, posts will not sit in the queue for very long. Also, it has been suggested that non-members who have a track record of good posts could be promoted to a usergroup that is not moderated. Over the next few weeks we'll decide if that's necessary.
Reply With Quote
  #19  
Old 2/6/09, 1:38 PM
Ed Fako's Avatar
Ed Fako Ed Fako is offline
Active Poster
 
Join Date: Feb 2007
Location: NW Chicago Suburbs
Posts: 199
Please Note: Ed Fako is a non-member guest and is in no way affiliated with InterNACHI or its members.
Default Re: Non-members can still post on this message board.

Thank you for the consideration.

I also left similar, but extended comments in a couple of other threads.

I do have a lot of experience or advice on how to maintain documentation for moderated members and posts from those other large forums I moderate on.

It need not be so time consuming and difficult by adding so many addditional tasks to the volunteers.

Ed
Reply With Quote
  #20  
Old 2/7/09, 1:49 AM
kpierce's Avatar
kpierce kpierce is offline
Active Poster
 
Join Date: Jun 2008
Location: Orting, WA
Posts: 4,609
Please Note: kpierce is a non-member guest and is in no way affiliated with InterNACHI or its members.
Default Re: Non-members can still post on this message board.

Quote:
Originally Posted by inxil View Post
Ed,

Once we have more moderators, posts will not sit in the queue for very long. Also, it has been suggested that non-members who have a track record of good posts could be promoted to a usergroup that is not moderated. Over the next few weeks we'll decide if that's necessary.
Glad to hear my suggestion is being considered.
Reply With Quote
  #21  
Old 2/7/09, 1:58 AM
John McKenna's Avatar
John McKenna John McKenna is offline
InterNACHI Member
 
Join Date: Jun 2006
Location: Crockett, Tx
Posts: 12,302
Default Re: Non-members can still post on this message board.

Quote:
Originally Posted by kpierce View Post
Glad to hear my suggestion is being considered.
I agree.



John McKenna, CMI (TREC #4565)
Executive Director - Master Inspector Certification Board
25 Yrs Constr Exp - 13 Yrs Home Inspector Exp
American Home Inspection - East Texas.

Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Olsen furnace age cbono Canadian Inspectors 7 7/5/08 11:05 PM
NH licensing prussell Legislation, Licensing & Legal Issues for Inspectors 12 5/21/08 4:40 PM
TAREI Members Petition badair Miscellaneous Discussion for Inspectors 0 10/30/07 6:50 AM
Tidbits from the ASHI Message Board jbushart Miscellaneous Discussion for Inspectors 126 4/27/07 11:05 AM


All times are GMT -4. The time now is 4:57 PM.


Popular Sections

:

All Sections

Inspection News

InterNACHI Membership

Inspection Standards

Inspection Education

InterNACHI Inspectors

Inspection Links

 

 

 

NACHI.ORG Statistics

 

 

no new posts